| NC-swivel head (B-axis) |
Controlled NC-swivel milling head (B-axis)
with clamping in position. Continuously positioning NC swivel milling
head with integrated motor spindle for 4/5 axes positioning and
simultaneous machining. Swivel torque: 3,300 / 2,300 Nm // 2,433 /
1,696 ft |
| Dynamic package for DMF 300|11
linear |
Dynamic package for DMF 300|11 linear Linear motor
X-axis with 80 m/min // 262.48 ft/min Rapid speed XYZ 80 m/min //
262.48 ft/min Acceleration XYZ 8 m/s² // 26.25 ft/s² Active cooling
for Linear motor |
| Package Mill / Turn 12,000 rpm,
HSK-A100 |
Package Mill / Turn, 12,000 rpm HSK-A100 (Only
available for Siemens 840D solutionline) NC-Mill-Turn-table d 1,050 mm
/ 41.3 in (left) C-axis direct drive, speed max. 700 rpm Integrated
balancing system Milling spindle power 44/32 kW (40/100% ED) tool
hol |
| Cabine |
Full protection cabin |
| NC-subtable 700-1, A-axis, left working
area |
NC-sub table 700-1 (A-axis) Left working area |
| Removable partition wall DMF |11 |
Partition wall removable for pendulum machining, 2
working spaces |
| Internal Coolant Supply 80bar/980l
frequency controlled |
Internal coolant supply (ICS) with paper type
filter Papertype-Filter 20-80 Bar // 290-1160 psi frequenzy controlled
980 l tank // 258.8 gallon inclusive 2 rotating clear window, air
purge for linear measuring system, rotary joint for main spindle |
| Coolant tempering for internal coolant
980l |
Coolant tempering for internal coolant unit 980l /
259 gallon: Heating capacity max.: 4 kW / 5.3 hp Cooling capacity
max.: 4 kW / 5.3 hp (only in combination with internal coolant unit
980l) |
| Chip flushing for working area |
Flushing for working area Additional flushing of
the working area doors and cabin sidewalls, Bed flushing included
(only available starting internal coolant supply 980l) |
| Air blast through spindle centre |
Air blast through spindle centre activated by M
function, maintained air, low oil rate possible |
| Swarf conveyor, apron conveyor |
Swarf conveyor,type apron conveyor recommended for
large swarf and thread chips |
| Oil mist separator (with partition
wall) |
Oil and emulsion mist separator system 2 pieces
per machine implemented in right and left cabin side wall. mechanical
filter system 2x1600 m³/h |
| Infrared measuring probe PP60
optical |
Infrared touch Probe for ISO 50 make Renishaw PP
60 optical (OMP 60) Tool taper suitable for the spindle |
| Combi-Tool measuring |
Combi - Tool measuring Blum LaserControl LC52
DIGILOG Laser-System for milling tools 3D-probe for turning tools |
| 3D quickSET elevated constructuion |
3D quickSET Tool kit for control and compensation
of the cinematic accuracy of 5 axis machine configurations include
additional fixture for elevated D4452871 construction (only with
option touch probe) |
| Sensor package i4.0 |
Sensor package i4.0: MPC Machine Protection
Control SGS Spindle Growth Sensor ICS flow sensor |
| Door drive for working area doors |
Door drive for working area doors Open / close -
activated by two-hand-operation at the control panel Safety sensor
technology for prevention of accidents |
| Signal lamp 4-colour |
Signal lamp, 4 colours |
| ATC (Application Tuning Cycle) |
ATC (Application Tuning Cycle) programmable feed
parameter selection for machining task: accuracy/surface/speed |
| Operation mode 4 |
Operation mode 4 Process monitoring in the
production Manual intervention with open doors of machining area.
Release after check list has been filled in. |
| Digital Manufacturing Package |
Digital Manufacturing Package (1) IoTconnector
Allows the use of the Online services from DMG MORI (2) Machine Data
Connector (MDC) Standardized machine data interface Protocols: OPCUA,
MTConnect, MQTT (3) NETservice Qualified support through
internet-b |
| Service Agent |
Service Agent Overview of all maintenance work on
the machine |
| Messenger V4 |
The latest version of DMG MORI Messenger displays
web based the machine live status. It allows to analyze the machine
run-time, downtime, alarms in individually configurable dashboards
and transparently shows the actual status in the manufacturing
shop |
| Special equipment |
- Tool magazine 30 places SK50/HSK-A100 Chain
magazine with double gripper - Additional control panel at tool input
station Mirrored tool list (control panel) - Adaptive coolant supply
Automatic optimisation and control of the ICS flow rate
depe |